Step Plumbing Guide for Installing a Bathtub
Step Plumbing Guide for Installing a Bathtub
Blog Article
We've encountered the article about Tools You Need to Install a New Bathtub listed below on the net and reckoned it made good sense to relate it with you on my blog.
Installing a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably hard project. If the old bathtub is easily available, the task can relocate rapidly; if you need to open up a wall surface to remove the old bathtub and place the brand-new tub, the task is much harder. In either case, the task is within a home handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. See to it you have qualified on your own for the task and are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed job, it is far better to consider using one before you start. Possibilities are you might require an expert plumber to make tube links.
This write-up will help you install a new bathtub in your bathroom if you have currently gotten a new tub and do not require to alter the setup of your previous water supply pipelines.
Your tools and material list need to make up the following:
Preparing for the Installment
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets system to stop pressure on the bathtub.
Fit the versatile tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing taps can be rather problematic as a result of the limited accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Utilizing both wooden boards under its feet, put the tub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny points.
The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost versatile tap port to the proper supply pipeline by making a compression join; then do the exact same for the other tap.
Activate the water and examine all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill the bathtub and likewise examine the overflow outlet and also the typical electrical outlet for leakages.
Finally, take care of the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub ought to wait until the tub has been used a minimum of when as this will certainly settle it right into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the maker provided backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap ports. The former type needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a stiff seal, creating the water to pass through the wall between the bath and also the tiling, leading to problems with moisture as well as feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly load the tub with water before sealing, to permit the motion experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly available on the market. It is advisable to fit the floor tiles using water-resistant or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about Installing A Bathtub? Make a remark down the page. We'd be interested to find out your thoughts about this review. Hoping to see you back again in the near future. For those who enjoyed reading our post if you please remember to share it. Thank you for taking the time to read it.
Contact Us Today Report this page